Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has lot of positives. It's stylish, it drives well and has a big boot. But can it beat off strong competition in the most crowded segment of the market?
If your Peugeot key fob isn't functioning, it may have been exposed to clean tap water or soapy water. It may be necessary to remove the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by a coin-sized battery. The power used to control the remote locking mechanism and other functions. The battery has a short time of life and will wear out over the course of years of use. Testing the voltage is a simple method of determining if the battery is defective. A multimeter is used to measure the voltage that is between the battery's plus and minus poles. The results of this test will reveal whether the battery is dead or not.
The receiver module could be the cause of your key fobs not working after having used your Peugeot 3008 a long time. The receiver module is in charge of receiving radio frequency signals transmitted by key fobs and then sending them to car systems. If the receiver module has problems, it won't be able transmit commands to the other modules in the car.
Another reason for the key fob not working is moisture or sweat in the circuit board. This can cause short circuits that drain the battery and disable the remote locking feature of the key fob. If this happens then you must bring your key fob to a chip level service technician to repair it.
Water damage
If you dropped your key fob into the pool, tossed it in the wash or even left it in the rain for too long, water damage could cause a lot of problems. Water is a great conductor, and it can short out circuit boards. It can also cause corrosion to the metal connections on the key fob and other components. A wet circuit could cause the battery to lose charge.
If you have an extra key fob, use it to unlock or lock the Peugeot 3008 to determine if a dead coin-cell battery as the reason for the problem. Another issue that can prevent your key fob from functioning properly is interference signals that interfere with the signal sent to the receiver module. These interference signals are caused by several sources, including radio transmitters within the vicinity.
If you hear sloshing sound emanating from your Peugeot 3008 while driving, it's likely because of a blocked condensate drain in the evaporator. You can test this by blowing compressed air through the drain holes in your door. You can also use flexible metal wire for wriggling drain holes to get rid of any dirt that has accumulated. Air pockets can be identified by sloshing sound.
A malfunctioning receiver module
The receiver module inside a Peugeot 3008 key fob is responsible for transmitting the remote keyless system signal from the key fob to the car's receiver. If the receiver module is damaged, it may cause the car to not recognize the key fob. This issue could be caused by a dead battery or water damage. Also, interference from electronic devices operating at the same frequency. In these cases there may be a message saying "card not detected" may appear on the display.
Luckily, there are a number of ways to troubleshoot this issue. You can try replacing the battery, or reprogramming the key fob. You could also start your vehicle with a spare key. If the key fob still isn't working after completing all these steps, it could have a faulty chip.
G28 is best to take out the chip and clean it using paper towels and rubbing alcohol. If the chip is damaged, you must purchase an entirely new one. FB Series enclosures are designed for use with a key fob. They come with a coin cell battery holder that is compatible with the most common types of key fob batteries. They can also be customized with digital printing and CNC cutouts that are machined. If your key fob was exposed to salty or dirty tap water, it is possible that the chip has been contaminated.
Keyless entry system malfunctions
If you get the message "card not detected" this signifies that your car can't receive signals from your key fob. This could be due to a number of reasons, such as an insufficient or dead battery. The issue can be resolved by pressing the start button on the key fob. In certain instances, however, you may have to take the key fob to an Peugeot dealership for additional repairs.
The battery test is the first step in diagnosing the problem with a Peugeot 3008 keyfob that doesn't lock or unlock doors. Batteries are the primary cause of a malfunctioning fob however there are a variety of other factors that contribute to this issue as well. This includes worn buttons, damage to the receiver module, water issues and signal interference.
If you've recently been exposed to water and have your Peugeot key fob exposed to clean tap water, it's a good idea to remove the battery and dry the electronic components using paper towels. You can also use a cleaner or isopropyl ethanol for this. It is recommended to replace the fob after it has been exposed to salt water or soapy water.
If your key fob not working, try to reset it by disconnecting the battery at 12 volts for approximately 15 minutes. Then reconnect the negative cable first, followed by the positive cable.